How to Reset Amana Ice Maker

You can How to Reset Amana Ice Maker by locating the small reset button on the side of the ice mold or by power cycling the unit for five minutes. This process typically takes about ten minutes to complete, though it may take up to 24 hours for the ice bin to fill completely after the reset. This method is best for homeowners dealing with simple mechanical jams or sensor errors that stop ice production.

Tools for resetting your Amana ice maker

How to Reset Amana Ice Maker
  • A sturdy flashlight: You need to see deep into the freezer or behind the ice bucket, where shadows often hide the small reset switch. A high-lumen LED light is best here, as dim bulbs often fail to illuminate the recessed corners where the switch is typically mounted.

  • A flat-head screwdriver: This helps if you need to gently pry the ice bin loose. Use it only as a lever on the designated plastic tabs. If you force it against the freezer wall, you risk cracking the liner, which costs hundreds to repair.

  • Clean, dry towels: These prevent water from pooling on your freezer floor if the ice maker has partially melted. Lay two thick towels down before you begin. If the floor is already wet, skip the reset until the unit is dry to avoid a short circuit.

  • A notepad and pen: Keep these nearby to write down any error codes shown on the digital display. If the reset fails, these codes are the only way to diagnose a failed control board.

  • Safety glasses: These protect your eyes from loose ice chips that can fly out when you move the bin.

  • Manufacturer manual: Always keep your documentation handy to verify the reset switch location. If you lack the manual, check the model number on the freezer’s back wall. Never use metal tools to chip away ice, as puncturing the evaporator coils will instantly ruin the cooling system.

How to Reset Amana Ice Maker: Step-by-Step

  1. Locate the reset button: Open your freezer door and remove the ice storage bin. Look for a small, recessed red or black button on the side of the ice maker assembly.
  2. Press and hold the button: Push the reset button firmly for about ten seconds. You might hear a click or a chime, which tells you the system is restarting its internal cycle.
  3. Check the wire shut-off arm: If your model uses a metal wire arm instead of a button, ensure it’s in the “down” position. If the arm is stuck in the “up” position, the ice maker thinks the bin is full and won’t produce more ice.
  4. Power cycle the appliance: If the button doesn’t work, unplug the refrigerator from the wall outlet. Leave it disconnected for at least five minutes to allow the control board to fully discharge.
  5. Reconnect the power: Plug the unit back in and allow it to run for two hours. During this time, the system performs a self-diagnostic test to check for sensor issues.
  6. Clear the ice chute: Use a plastic utensil to gently remove any ice blockages in the dispenser chute. If you force the ice, you risk breaking the plastic flap.
  7. Verify the water supply: Check that the water line behind the fridge isn’t kinked or frozen. If the water supply is restricted, the ice maker won’t cycle even after a successful reset.

Careful: If you hear a grinding noise during the reset, stop immediately and check for a physical obstruction. Forcing a jammed motor can strip the internal gears.

💡 Tip

If the reset fails repeatedly, the control board might be faulty. Contact an authorized repair technician to avoid voiding your warranty.

How it changes with the situation

The time and effort required to restore ice production depend on the nature of the blockage. It’s always safer to start with a simple power cycle before moving to manual mechanical adjustments.

SituationTime NeededDifferenceWatch For
Minor Ice Jam10 MinutesManual clearingSharp ice edges
Control Board Error30 MinutesNeeds power cycleDisplay error codes
Frozen Water Line2 HoursNeeds heat/thawWater leaks
Broken Motor24 HoursRequires partsGrinding sounds

Most users make the mistake of using a hairdryer on full heat to clear a frozen line. This often melts the plastic housing, turning a simple thaw into a total unit replacement. If the line is frozen, use a warm, damp cloth instead.

Apply this decision rule: if the ice maker is silent, check the power board first. If you hear a rhythmic clicking or humming, the motor is likely stalled by a physical obstruction. Never force the ejector arm by hand, as the plastic gears are brittle and snap under pressure.

How to tell you did it right

Freshly formed ice cubes inside an Amana refrigerator ice maker mold.
Photo: www.youtube.com on Google

A successful reset shows itself when you hear the water inlet valve open after the cycle begins. Within two hours, you should see the ice maker arm move or hear the mechanical sound of the rake rotating. If you see ice cubes forming in the mold, you have solved the issue.

A poor result occurs if the ice maker remains silent or if the water valve hums but no water enters the tray. This usually happens because the water supply line is frozen or the filter is completely clogged. If the tray stays dry despite the valve humming, check the supply line for a kink or a frost blockage.

To prevent this, replace your water filter regularly and ensure the freezer temperature stays at or below zero degrees Fahrenheit.

Troubleshooting and Maintenance Standards

After resetting your unit, ensure the ice bin is seated firmly on the tracks. If the bin sits at an angle, the sensor won’t trigger correctly, and the unit will shut down again. Most modern units require a flush-fit; if you see a gap larger than a nickel between the bin and the housing, the safety switch remains open.

Clear away any frost buildup on the back wall, as this can insulate the sensors and give false readings. A common mistake is using a metal tool to chip this ice, which risks puncturing the evaporator coils. Use a plastic scraper or a warm cloth instead.

If you notice a persistent leak or the reset button remains stuck, this isn’t a user-serviceable task. Contact a certified appliance repair professional to handle internal electrical components, as these carry high-voltage risks. Keep a log of your reset dates.

Other ways to do it

Manual Thaw

If the ice maker is frozen solid, use a hair dryer on a low, cool setting. Move it back and forth across the ice maker housing to melt the buildup. Don’t hold it in one spot, as high heat will melt the plastic components and ruin the assembly permanently.

Water Filter Bypass

Sometimes the filter is clogged, blocking water flow. Remove the filter and install a bypass plug if your model came with one. If the ice maker starts working, you know the old filter was the cause and simply need to buy a new, compatible replacement.

Diagnostic Mode

Many newer models have a hidden diagnostic mode. Consult your manual to find the specific button combination to enter this mode. It will run a test cycle and display an error code on the front panel, which helps you pinpoint exactly which sensor has failed.

Frequently asked questions

A person checking the Amana refrigerator manual for troubleshooting and frequently asked questions.
Photo: www.appliancepartspros.com on Google

Can I reset my Amana ice maker by holding the power button?

Yes, on many newer models, holding the power button for three to five seconds will toggle the ice maker off and on, which acts as a soft reset. If your model doesn’t have a dedicated power button, you must use the physical reset switch located inside the ice maker housing or perform a full power cycle by unplugging the refrigerator.

Why does my ice maker stop working after a few days?

This usually happens because of a frozen fill tube or a failing water inlet valve. When the fill tube freezes, the water can’t reach the tray, and the ice maker senses an error. Check the tube for ice buildup and use a warm, damp cloth to melt it. If the problem continues, the inlet valve may be leaking, which requires a professional to replace.

How long should it take for the first batch of ice?

You should wait at least 24 hours after a reset for the ice maker to reach its full production capacity. The first few batches are often discarded by the system as part of a self-cleaning cycle, so don’t be alarmed if the bin remains empty for the first few hours.

Is it safe to use a screwdriver to clear ice?

No, never use a metal screwdriver to chip away ice near the coils or the ice maker assembly. You risk puncturing the sealed refrigerant system, which is a major repair that often costs more than the refrigerator itself. Always use plastic or wood tools to gently nudge ice blockages.

What happens if the reset button doesn’t click?

If the button doesn’t click, the switch may be stuck or the unit may be completely dead. Check your home circuit breaker to ensure the refrigerator has power. If the fridge is running but the ice maker remains unresponsive, the internal motor might be jammed, requiring a repair technician to inspect the assembly.

How do I know if the water line is the problem?

You can verify the water line by checking if your water dispenser works. If the dispenser also lacks water, the problem is likely the supply line or the water filter, not the ice maker itself. If the dispenser works but the ice maker does not, the issue is internal to the ice maker unit.

Final Thoughts

If your ice maker still isn’t working after these efforts, there might be a deeper issue with the water line or the control board. Don’t hesitate to check your owner’s manual for specific troubleshooting codes. If you’re still stuck, it’s best to call a professional technician to get things running again.

Leave a Comment