Wrx735Sdbm00 Ice Maker Not Working

A frozen water line or a stuck ice mold is the reason for a Wrx735Sdbm00 Ice Maker Not Working most of the time. You can usually confirm this by checking the water line behind the fridge or looking for a block of ice inside the ice bin. Always consult your owner’s manual for specific reset procedures before assuming the system is broken.

Why your Wrx735Sdbm00 Ice Maker Not Working

Wrx735Sdbm00 Ice Maker Not Working
CauseHow commonHow to confirm itFix it yourself?
Frozen water lineVery commonCheck tube for iceYes
Jammed ice cubesCommonInspect ice moldYes
Water filter cloggedCommonCheck filter life lightYes
Water valve failureOccasionalListen for water humNo
Control board errorRareReset the fridgeYes
Broken motorRareNo ice movementNo

If you see a solid plug at the dispenser nozzle, use a hair dryer on a low setting for three minutes to clear it.

Distinguish a jammed mold from a broken motor by listening closely during the harvest cycle. If you hear the motor whirring but the tray stays inverted, a cube is physically obstructing the rotation.

A clogged filter is the most common mistake owners make, often costing them unnecessary repair calls. If the water flow is weak but the ice maker is silent, change the filter before assuming a valve failure.

Frozen water supply line

A frozen water line prevents liquid from reaching the tray, which stops the freezing cycle entirely. This happens when the temperature inside the freezer fluctuates or the water inlet tube sits too close to the cooling coils. You can identify this by pulling the refrigerator away from the wall to inspect the plastic water line at the back. If you see a solid kink or a section that feels hard and cold instead of flexible, it’s likely frozen.

To address this, you must allow the ice to melt naturally. Unplug the refrigerator or turn off the ice maker power switch for at least four hours. This gives the line enough time to reach room temperature. If the blockage persists, use a hair dryer on a low, cool setting directed at the water tube near the back of the cabinet. Keep the dryer at least six inches away to avoid melting the plastic housing. Never use a sharp object to poke the line, as this causes leaks that are difficult to repair.

This fix takes about 30 minutes of active time, but the wait for the ice to melt is the main delay. Follow the Whirlpool refrigerator temperature guidelines to ensure your unit stays within the recommended range. If you still have issues, the door seal might be leaking warm air into the freezer compartment, which creates condensation that freezes the water line.

Ice jam in the mold

An ice jam occurs when cubes get stuck in the ejector fingers or the harvest tray. You can tell this is the issue if you see partial cubes or a large clump of ice blocking the mechanism inside the tray. This often happens if the water pressure is too low, causing the machine to fill the tray only halfway, which leads to tiny or “hollow” cubes that break and lodge themselves in the ejector.

To clear this, turn off the ice maker and remove the ice bin entirely. Use a plastic utensil to gently nudge any stuck ice away from the fingers. Don’t use metal tools, as these scratch the non-stick coating of the mold and lead to permanent sticking later. Once the mold is clear, wipe the sensor area with a dry cloth to remove any frost buildup. If the tray is completely blocked by a solid chunk of ice, use warm water on a towel to melt the bond.

This process takes about 15 minutes. If you find the cubes are consistently small, check your water line pressure. The system requires a steady flow to function correctly; if your home water pressure is low, the ice maker won’t fill enough to trigger the harvest cycle. This isn’t for you if you can’t reach the back of the machine or if you feel uncomfortable handling the internal plastic components of the ice maker assembly.

Clogged water filter

A hand removing a water filter cartridge from a modern refrigerator housing.
Photo: www.appliancepartspros.com on Google

A restricted water filter slows the flow of water to the ice maker, leading to thin cubes or a complete stoppage. You can confirm this by checking the filter status light on your control panel. If the light is red or has been on for more than six months, the filter is likely the culprit. Even if the light is off, a filter that hasn’t been replaced in over a year can restrict flow enough to stop the ice maker from filling.

To fix this, locate the filter housing—usually found at the top right corner of the fridge or in the base grille. Twist the old filter counter-clockwise to remove it and insert the new one by twisting it clockwise until it clicks. After replacing the filter, run at least one gallon of water through the dispenser to clear air from the lines. This ensures the ice maker receives a full charge of water for the next cycle.

The cost depends on the specific filter model required for your fridge. Always verify the part number on your current filter or inside your manual before buying a replacement. Using an incompatible filter can cause leaks or prevent water from flowing entirely. This is a simple task, but if the water still doesn’t flow after a filter change, the internal water valve might be faulty. At that point, you should contact a professional, as replacing the valve involves handling electrical connections and water lines inside the cabinet.

The less likely causes

  • Failed water inlet valve: The solenoid that opens the water line has stopped working. You can confirm this if the fridge dispenses water through the door but the ice maker stays dry. If the valve fails to open, the mold never fills, preventing any ice production.

  • Defective harvest motor: The internal motor that rotates the ice tray has burned out. The unit remains stuck in one position despite a hard reset. If you hear a faint humming but no movement, the gears have likely stripped.

  • Broken ice level sensor: The infrared sensor that detects bin capacity is malfunctioning. The system incorrectly assumes the bin is already full. Check for frost buildup on the sensor eyes; wiping them with a dry cloth often restores functionality.

  • Control board failure: The main computer has stopped sending signals to the ice maker. This requires a professional to diagnose. If you have verified power at every other component, the board is the final suspect.

What a fix usually involves

Most repairs for this model involve either a simple reset or replacing a low-cost part like a water filter. If the issue is a frozen line, the only cost is your time spent waiting for the ice to melt. You can confirm this by checking if the water dispenser works but the ice maker remains jammed.

If you need a new water filter, expect to pay a moderate amount for a genuine part. Avoid generic versions, as they often don’t seat correctly and can cause leaks that damage your flooring. A faulty water valve or control board is a more significant repair. These parts are expensive, and the labor required to safely disassemble the appliance means the total cost can represent a large portion of the price of a new unit.

Use this decision rule: if the repair quote exceeds 50% of the cost of a new machine, prioritize replacement. Check the official manufacturer website to see if your model is covered under any specific recalls or extended warranty programs before paying for a service. Always get a written quote from a certified technician to compare the repair price against the cost of a new appliance. Many people make the mistake of assuming a repair is always cheaper, which often leads to sinking money into a failing machine.

Frequently asked questions

Troubleshooting tools and a digital guide placed on a clean kitchen countertop.
Photo: www.youtube.com on Google

How do I reset the ice maker?

You can reset the unit by turning the power switch to the off position for 30 seconds and then back on. Some models also allow a reset by holding the “Ice” and “Light” buttons simultaneously for three seconds. If the unit doesn’t respond, check your manual for the specific reset sequence for your serial number, as this varies by model.

Is it safe to use a hair dryer to melt the ice?

Yes, but only if you use the lowest heat setting and keep the dryer at least six inches away from the plastic. Never touch the plastic with the nozzle, as the heat can warp the internal components or melt the water line. If you don’t feel comfortable using heat near the fridge, simply unplug the unit and leave the freezer door open.

How long does it take to make a full bin of ice?

About 24 hours is the standard time required for a new ice maker to fill a bin after being turned on. If the bin is still empty after a full day, verify that the water supply is turned on and that your freezer temperature is set to the recommended setting, typically zero degrees Fahrenheit.

Does the water filter age affect ice quality?

Yes, an old filter can cause cloudy or bad-tasting ice, or it can block water flow entirely. You should replace the filter regularly to ensure the water quality remains high. If you live in an area with hard water, you may need to replace it more often to prevent mineral buildup inside the machine.

What happens if the ice maker is still not working after these steps?

If you have checked the water line, replaced the filter, and performed a reset without success, the problem is likely an internal electrical failure. At this point, the repair moves beyond a simple DIY fix. Contact a qualified technician to inspect the water valve or control board, as these tasks require specific tools and knowledge of the appliance’s wiring.

Final Thoughts

If these simple checks don’t get your ice flowing again, it’s time to reach out to a professional technician. Don’t hesitate to call for help if you’re uncomfortable handling the internal components. Getting a pro’s opinion will ensure you don’t accidentally damage your appliance while trying to fix the cooling system.

Related guides

Leave a Comment