You can perform a manual reset by disconnecting the power for sixty seconds and then cycling the function knob through specific positions. This simple procedure clears minor electronic glitches and helps you How to Reset Roper Washing Machine when the control board becomes unresponsive or stuck in a cycle. This method works well for most digital-interface models, though it isn’t intended for mechanical timer issues where a physical part has failed.
Tools to reset your washing machine

To complete this process safely and effectively, you’ll need a few basic items. Ensure you have the following ready before you begin:
A stable step stool: Use this to reach the power outlet if it’s mounted high on the wall behind the machine. Avoid using chairs with wheels or unstable folding stools, as they can slip under the weight of the appliance.
A timepiece or phone: You need to track the sixty-second wait time accurately. Counting in your head is often too fast; use a digital timer to ensure the capacitors fully discharge.
Flashlight: This helps you see the control dial markings if your laundry area is dimly lit. Don’t rely on ambient room lighting, as you must precisely align the dial to the reset position.
Dry hands: Always ensure your hands are completely dry before touching the power plug or the control panel to prevent electrical shocks.
If you have a built-in timer, you may need a small flathead screwdriver to gently pry off a stuck knob. If the knob feels resistant, stop immediately. Forcing it will snap the plastic D-shaft, turning a simple reset into a costly repair.
Inspect the control board for visible charring or a sharp, acrid smell. If the board is physically damaged or burnt, a reset won’t fix it. In this case, consult the Whirlpool product support page to identify your specific model’s diagnostic codes.
If you aren’t comfortable working with electrical components, contact a professional technician. Attempting to bypass a damaged fuse or wire can lead to a fire hazard.
How to Reset Roper Washing Machine: Step-by-Step
- Turn the control dial to the “Normal” or “Off” position to clear any current active settings.
- Unplug the washing machine from the wall outlet or flip the circuit breaker to the “Off” position. A capacitor can hold a lethal charge even when unplugged, so never attempt to open the machine housing or touch internal wiring.
- Wait exactly sixty seconds with the power disconnected to allow the internal memory to clear completely.
- Plug the machine back in or flip the circuit breaker back to the “On” position.
- Observe the status lights on the control panel to see if they start blinking, which indicates the machine has entered its internal diagnostic or reset mode.
- Select your desired wash cycle and press the “Start” button to verify if the machine operates normally again.
If the lights don’t blink during step six, repeat the rotation sequence more slowly, as the timing of the clicks is critical for the processor to register the command.
Careful: If you hear a loud buzzing noise or smell burning plastic after plugging the unit back in, immediately disconnect the power again and don’t attempt further resets.
Operational reset variables
The process changes slightly depending on your control panel type and the current state of the machine’s memory.
| Situation | Time Needed | Difference | What to watch |
|---|---|---|---|
| Minor glitch | 60 seconds | Basic power cycle | Status lights |
| Stuck cycle | 2 minutes | Full dial rotation | Blinking patterns |
| Power surge | 5 minutes | Breaker reset | Control panel response |
| Sensor error | 10 minutes | Clear drum load | Error codes |
Most users mistakenly jump to a breaker reset before checking the drum load. This oversight costs you time and risks damaging the internal logic board by cutting power during an active cycle.
If the control panel remains dark after a power cycle, check your GFCI outlet first. If the outlet is tripped, the machine isn’t the problem. If the panel lights up but shows an error code, don’t force a restart. Instead, clear the drum completely. A heavy, unbalanced load often triggers a false sensor error that prevents the machine from engaging the motor.
Use this decision rule to save your hardware: if the error code persists after clearing the drum, the sensor is likely faulty. If the machine runs but stops mid-cycle, the issue is a voltage drop. In that case, move the unit to a dedicated circuit to prevent recurring power surges. Always prioritize the simplest reset first, adding complexity only when the machine remains unresponsive.
How to tell you did it right

A successful reset is apparent when the control panel lights stop flashing erratically and remain steady once you select a cycle. If you previously saw a specific error light pattern, those lights should now be extinguished.
A poor result occurs if the machine starts to fill but stops immediately or if the same error lights reappear within a few seconds of starting the cycle. This usually happens because the underlying mechanical issue, such as a faulty lid switch or a clogged drain pump, remains unresolved.
The primary mistake users make is ignoring the drain hose. If the hose sits more than 96 inches above the floor, the pump can’t clear the water, triggering a false error code that mimics a board failure. Check your installation height before assuming the electronics are dead.
If the unit still fails, it often points to a failed sensor or a damaged control board that requires a professional assessment. Use this decision rule: if the lights return while the machine is empty, the issue is internal circuitry. If the lights return only after the machine attempts to draw water, the issue is a physical blockage or a faulty intake valve.
Proper Maintenance and Safety
Adhere to the manufacturer’s guidelines regarding the maximum weight capacity, as specified by the Roper owner’s manual, to avoid overloading the sensors. Overloading is the most frequent cause of the machine locking its interface as a safety precaution. If the display flashes an “F” code, you have likely exceeded the 15-pound limit for delicate cycles or the 25-pound limit for standard loads.
After a successful reset, wipe the control panel with a dry cloth to prevent moisture from entering the electronics. Even minor condensation can cause short circuits in the touch-sensitive membrane. Ensure the machine sits perfectly level on the floor to reduce vibration.
If you notice persistent issues, check the Consumer Product Safety Commission website to see if your specific model has a known safety recall. Many users mistake a faulty door latch for a sensor error, leading them to bypass safety switches. This is a dangerous practice that voids your fire insurance. If the machine requires a part replacement, this isn’t a do-it-yourself job. A technician must handle all internal repairs to maintain your safety and warranty. If the unit emits a burning smell, disconnect the power immediately and wait for professional service.
Other ways to do it
Using the lid switch
This bypasses the dial sequence but only works on models with specific sensor-equipped lids.
Checking the circuit breaker
If the dial sequence fails, the issue might be a tripped GFCI breaker in your home. Instead of resetting the machine, go to your main electrical panel and ensure the breaker for the laundry room is fully engaged.
Disconnecting the water supply
This is useful if the machine thinks it’s full when it’s actually empty.
Frequently asked questions

Can I reset the machine while it’s full of water?
Yes, you can perform a reset while water is in the drum, but be aware that the machine may attempt to drain immediately once the reset is successful. Ensure your drain hose is connected properly to a standpipe or laundry tub to prevent flooding your floor during this process.
Why does my machine reset itself during a cycle?
This usually happens because of a loose power connection or a failing lid switch that signals the board to stop for safety reasons. If this occurs, check the wall outlet for a tight fit and inspect the door latch for any debris that might prevent it from locking securely.
How long does a hard reset take?
A standard hard reset takes about sixty seconds for the power-down phase and another thirty seconds to perform the dial sequence. If you need to clear a persistent error code, allow up to ten minutes for the onboard computer to fully cycle through its diagnostic memory.
Is it safe to leave the machine unplugged for a long time?
Yes, it’s perfectly safe to leave the machine unplugged for as long as you need while you troubleshoot or wait for a technician. There’s no risk to the electronic memory of the machine, as it’s designed to hold settings even during long power outages.
What happens if the reset doesn’t work?
If the machine remains unresponsive, the fault likely lies with a physical component like the water inlet valve, the pump, or the main control board. At this point, stop attempting resets and contact a qualified appliance repair service, as further attempts won’t fix the mechanical failure.
Final Thoughts
If your machine still won’t start after you’ve tried these steps, it’s likely that a part like the lid switch or motor has worn out. Don’t hesitate to reach out to a local repair technician for help. Getting a professional opinion will save you a lot of time and unnecessary stress.