A Sun Joe Pressure Washer Not Working usually means your water supply is blocked, the power connection is tripped, or the air trapped in the system is preventing the pump from building pressure. First, check that your faucet is fully open and the garden hose isn’t kinked. If the motor hums but doesn’t spray, it’s almost certainly an air lock. If the unit is silent, the Ground Fault Circuit Interrupter (GFCI) on the power cord has likely tripped, which you can reset by pressing the reset button on the plug.
Reasons your pressure washer stopped working

Pressure washers rely on a steady flow of water to cool the internal pump components. When water flow is restricted, the pump struggles, leading to performance loss or complete failure. The most common cause is a clogged inlet filter. This small screen sits inside the water intake port and catches debris from your garden hose. If this screen is blocked, the pump can’t pull enough water to create pressure.
Another frequent cause is trapped air. If you connect your hose and turn on the machine before running water through the pump, air pockets get stuck inside the internal chambers. These pockets prevent the pump from priming. This is a common issue after moving the unit or disconnecting the water supply.
Finally, electrical safety features are designed to shut the unit down if they detect a fault. The GFCI plug is sensitive to moisture and power surges. If the unit was used during rain or if the outlet is damp, the internal safety mechanism will cut power to prevent electrical hazards.
Clear the inlet filter
This fix is for users who experience low water pressure or a machine that stops spraying after a few minutes. If the water flow feels weak at the nozzle, the intake screen is likely the culprit.
To clean it, first turn off the power and disconnect the unit from the electrical outlet. Remove your garden hose from the machine’s inlet port. Look inside the port to find the small mesh screen or plastic filter. Use a pair of needle-nose pliers to gently pull the filter out. If it’s covered in dirt or mineral deposits, wash it under a running faucet until the mesh is completely clear. Don’t use sharp tools that might tear the screen. Once clean, push the filter back into place until it sits flush. Reattach your garden hose and turn the water on fully before plugging the machine back in. If the pressure returns to normal, the clog was the only issue.
This isn’t for users who hear a grinding sound from the motor, as that suggests internal mechanical wear. If you clean the filter and the pressure remains low, the pump seals may be damaged. In that case, you should contact the manufacturer or a qualified service center, as internal pump repairs require specialized tools and parts.
Remove trapped air
This step helps if the motor runs but no water comes out of the spray wand. This happens when air occupies the space where water should be, stopping the pump from cycling properly.
Start by disconnecting the high-pressure hose from the machine. Turn on your water supply at the faucet and let it run through the machine’s outlet port for about 30 seconds. This flushes out the air pockets that prevent the pump from starting. Once you see a steady, bubble-free stream of water coming out of the outlet, turn off the water. Reconnect the high-pressure hose firmly. Next, attach your spray wand but don’t attach the nozzle tip yet. Turn the water back on, then hold the trigger on the wand down to let water flow through the system for another 30 seconds. This clears any remaining air from the hose and wand. Finally, attach your nozzle tip and turn the power on.
This fix is for air locks only. If the motor still doesn’t start or spray correctly after this process, the issue is likely electrical or a failed motor capacitor. Never attempt to open the motor housing, as a capacitor can hold a lethal charge even when the unit is unplugged. If the problem persists after clearing the air, you must take the unit to a certified repair shop.
Check electrical power

This fix is for units that show no signs of life, such as no lights or motor noise when you flip the switch. Before assuming the motor is dead, test the power source.
First, check the GFCI plug on the power cord. You’ll see two buttons labeled “Test” and “Reset.” Press the “Reset” button firmly. If it clicks into place, the plug was tripped. Now, check your home’s main breaker panel to ensure the circuit you’re using hasn’t tripped. If the outlet is working, plug in a different device, like a lamp, to confirm the outlet itself provides power. If the lamp works but the pressure washer does not, the issue lies within the machine’s internal wiring or the switch.
This is worth the time if the machine is still under warranty, as opening the case yourself will void it. If you have confirmed the outlet is live and the GFCI is reset, but the machine remains silent, don’t attempt further repairs. This indicates an internal component failure. Contact the manufacturer’s support line to see if your model is eligible for a replacement. If the warranty has expired, consult a local small-appliance repair shop to see if the cost of the repair is less than a new unit.
What not to do
Don’t use a pressure washer with a damaged power cord. The insulation is vital for your safety, and a frayed cord creates a high risk of electric shock when exposed to water. If you see exposed copper or wire casing, stop immediately. Replacing a cord costs far less than a trip to the emergency room.
Don’t attempt to open the motor housing. The internal components, including the capacitor, store lethal electrical charges long after the machine is unplugged. These parts require a professional technician to handle safely.
Don’t run the machine without water. Dry running the pump for even a few seconds can melt the internal seals, which permanently destroys the pump’s ability to create pressure. If the motor sounds high-pitched or whiny, shut it off instantly.
Don’t use harsh chemicals in the detergent tank. Using bleach or acidic cleaners can corrode internal pump seals and hose fittings, leading to leaks that are difficult to fix. Only use soaps specifically labeled for pressure washers.
Don’t force a clogged nozzle with a needle. Inserting a metal object can widen the spray orifice, which ruins the spray pattern. If water flow is uneven, soak the nozzle in white vinegar for an hour to dissolve mineral deposits instead of poking it.
How to stop it happening again
Regular maintenance ensures your machine remains reliable and keeps the pump working within its designed limits.
| If you’re doing this | Do this instead | Why |
|---|---|---|
| Leaving water in the pump | Flush with pump protector | Prevents freezing and mineral buildup |
| Using the machine in the rain | Only use on dry days | Reduces risk of GFCI tripping |
| Storing the unit outdoors | Store in a shed or garage | Protects seals from sun and moisture |
| Ignoring the intake filter | Rinse filter every use | Prevents debris from blocking the pump |
| Running with low water | Check faucet flow first | Ensures pump stays cool and lubricated |
If you notice the motor humming louder than usual, stop immediately. This indicates cavitation, meaning the pump is struggling to pull water. If the sound persists after clearing the intake, your pump valves or seals are likely damaged. You can distinguish between a clog and a mechanical failure by checking the output pressure; if the pressure is steady but weak, it’s a filter issue. If the pressure pulses, your seals are likely leaking air.
Frequently asked questions

Can I use an extension cord with my pressure washer?
You should avoid using an extension cord because it causes a voltage drop that can overheat the motor. If necessary, use a short, outdoor-rated cord with the correct gauge for your model’s amperage. Using an undersized cord often leads to premature motor failure.
Why does my pressure washer pulse on and off?
Pulsing usually occurs due to a leak in the high-pressure hose or a blocked nozzle. Check all connections for drips and ensure O-rings are seated correctly. If no external leaks exist, the internal pump seals may be worn and require professional service.
How long should a pressure washer last?
A typical home-use model can last several years with proper maintenance. Flush the pump after every session and store the unit in a temperature-controlled space. Heavy commercial use will significantly reduce the lifespan of internal parts.
Is it safe to repair the pressure washer myself?
No, you should never attempt to repair internal components like the motor, capacitor, or electrical switches yourself. These parts are dangerous and require professional training. You can safely clean the external intake filter, clear the nozzle tip, and reset the GFCI plug, but everything else is a job for a qualified technician. Attempting to open the housing carries a risk of electric shock and will void your manufacturer’s warranty immediately.
What happens if I let the pump freeze?
Water remaining in the pump during freezing temperatures will expand and crack the internal housing. Always store the unit in a space above freezing or use a pump antifreeze solution before winter. Running a frozen, cracked pump will cause further motor damage.
Final Thoughts
If these quick fixes don’t get your machine running, don’t worry. You should reach out to the manufacturer’s support team with your model number handy. They’ll help you determine if a part needs replacing or if your unit is still under warranty. You’ll be back to cleaning your driveway in no time.
Related guides
- Greenworks Pressure Washer Soap Not Working? Fix It Fast
- Why is My Greenworks Pressure Washer Not Working? Troubleshooting Tips
- Water Pressure Drops When Washing Machine is Running: Fix Fast