New Holland Ls170 Problems

A clogged hydraulic filter is the most common cause of New Holland Ls170 problems, appearing in most cases where the machine loses lift power or shows slow response times. You can verify this by checking the system pressure gauge against the manufacturer’s specified range found in the New Holland operator manual. This assumes the machine is at operating temperature; if the oil is cold, the pressure readings will naturally appear higher due to increased viscosity.

Common New Holland performance problems

New Holland Ls170 Problems
CauseHow commonHow to confirm itFix it yourself?
Clogged hydraulic filterVery commonCheck pressure gaugeYes
Worn drive beltCommonInspect for cracksYes
Air in fuel linesCommonCheck for bubblesYes
Weak batteryOccasionalTest voltage outputYes
Faulty lift solenoidOccasionalListen for clickYes with care
Hydraulic pump failureRareCheck pump noiseNo

If your pressure gauge needle fluctuates wildly during operation, the filter is likely choked with debris. Replace it according to the manufacturer’s recommended service interval.

Inspect drive belts by twisting them 90 degrees. If you see fraying or rubber dust on the housing, the belt is slipping and losing torque. A loose belt often squeals under a cold start; Tighten the belt to the manufacturer’s specified tension.

Air in fuel lines usually occurs after running the tank dry. Check the clear return lines for persistent bubbles while the engine idles. If the bubbles don’t clear after five minutes, you have a leak in the suction side of the fuel pump.

A weak battery often masquerades as a starter issue. Use a standard multimeter to test the battery voltage.

The lift solenoid should produce a sharp, metallic click when you toggle the switch. If you hear a dull thud or nothing at all, the coil is likely burnt out. Use a test light on the connector to verify power is reaching the unit before replacing the solenoid.

Hydraulic pump failure is unmistakable. If you hear a high-pitched whine or grinding metal, the internal gears are likely shattered. Stop the machine immediately to prevent metal shavings from contaminating the entire hydraulic circuit.

Hydraulic filter obstruction

A clogged filter restricts oil flow, which directly causes the hydraulic system to struggle under load. When the filter becomes saturated with debris, the bypass valve may open to protect the pump, but this allows unfiltered oil to circulate, leading to sluggish bucket movement and decreased lift capacity. You can confirm this issue by observing the hydraulic performance after the machine has reached its normal working temperature of approximately 140 degrees Fahrenheit.

To fix this, locate the hydraulic filter housing near the main pump assembly. Ensure the machine is turned off and the lift arms are safely blocked in a raised position to prevent accidental dropping. Unscrew the old filter using a standard filter wrench, coat the new gasket with a thin layer of fresh hydraulic oil, and hand-tighten the replacement. This process usually takes about twenty minutes. If you notice a high-pitched whining sound during operation, it indicates the pump is starving for oil, which means the filter is either severely blocked or the wrong micron rating was installed. Always check the label on your specific unit, as different model years may require a different filter element. This isn’t for those without basic mechanical experience, as spilled hydraulic fluid requires proper containment to avoid environmental damage.

Drive belt wear and tension

Close up of a worn and cracked drive belt on a machinery pulley.
Photo: www.youtube.com on Google

A worn drive belt causes the engine to lose power to the hydraulic pump and cooling fan, leading to overheating or poor machine performance. When the belt stretches or cracks, it slips on the pulleys, preventing the efficient transfer of power. You can distinguish this from a hydraulic fault by listening for a squealing sound when you engage the lift controls; if the engine RPM drops significantly while the belt squeals, the belt is the culprit. Inspect the belt for fraying or missing chunks along the inner V-grooves.

A common mistake is assuming a belt is fine because it looks intact. Even without visible cracks, a belt that has glazed over—becoming hard and shiny—will lose its grip. If you see a polished, mirror-like finish on the inner ribs, the rubber has lost its coefficient of friction and must be replaced regardless of its physical shape.

To address this, locate the tensioner pulley on the front of the engine block. Rotate the tensioner using a long-handled socket wrench to release the pressure, then slide the old belt off the pulleys. Install the new belt by following the diagram usually printed on a decal near the radiator shroud. If the belt is new but still slips, check that the tensioner spring isn’t fatigued. A healthy tensioner should offer firm, consistent resistance; if it moves with little effort, the spring is likely weak and requires a full assembly replacement.

This repair takes roughly thirty minutes. If you aren’t comfortable working with heavy-duty tensioners, contact a technician, as a snapping belt under tension can cause injury. This varies by model; check the label on your engine compartment for the exact belt part number to ensure you have the correct length and width. Always verify the belt sits deep within the pulley grooves; if it rides on the outer edges, the pulley alignment is likely compromised.

Fuel system air pockets

Air in the fuel lines prevents the engine from receiving a steady supply of diesel, leading to rough idling or sudden stalling under load. This is distinct from hydraulic issues because the engine itself will sputter or die, rather than just losing lift strength. You can confirm this by checking the clear fuel lines for air bubbles while the engine is running or by priming the manual fuel lift pump located on the side of the engine. If the primer feels soft or “mushy” instead of firm, air is present in the system.

To fix this, loosen the bleed screw on the fuel filter housing and operate the manual primer until only pure fuel flows out without bubbles, then tighten the screw. This task takes about fifteen minutes. If the problem persists, check the fuel lines for small cracks or loose clamps that might be sucking in air during operation. If you find cracks in the rubber lines, replace them immediately to prevent a fire hazard. This is a common mistake for owners who ignore small leaks, which eventually lead to a complete engine failure on the job site.

If you can’t achieve a firm primer feel after three cycles of bleeding, the issue is likely a failed check valve or a pinhole leak in the fuel pickup tube inside the tank. In this case, don’t keep cranking the engine. Excessive cranking can overheat the starter motor or drain the battery completely.

The decision rule is simple: if the fuel flows clear but the primer remains soft, the leak is on the suction side of the pump. If the fuel remains frothy, the leak is between the pump and the filter. Always inspect the copper crush washers on your banjo bolts first, as these are the most frequent culprits for recurring air intrusion after a filter change.

The less likely causes

Cleaning corrosion from a battery terminal on a piece of industrial machinery.
Photo: www.boomandbucket.com on Google

Electrical ground faults often cause intermittent sensor warnings. You can verify this by inspecting the battery terminals for corrosion or loose mounting bolts. If the metal surfaces appear dull or chalky, clean them with a wire brush and baking soda solution. A clean connection restores the circuit path and prevents phantom error codes from triggering.

Worn joystick bushings cause “sloppy” control inputs. You can identify this by measuring the excessive play in the handle before the machine reacts. If the handle moves more than half an inch without engaging the hydraulic valve, the bushings have reached their service limit. Replacing them now prevents permanent damage to the linkage pins.

A failing alternator results in a dim dashboard display and weak lights. Use a multimeter to check the alternator output voltage.

Hydraulic cylinder seal leaks show up as visible oil weeping near the rod end. This requires a specialized rebuild kit. Don’t ignore this; a minor weep often precedes a catastrophic seal blowout that can dump gallons of fluid in minutes.

If the machine refuses to start, check the safety interlock switches. This is a task for a qualified technician if the wiring is damaged. A common mistake is bypassing these switches, which voids warranties and creates a severe crush hazard for the operator.

What a fix usually involves

Most repairs for these issues require basic hand tools like a socket set, a filter wrench, and a pair of pliers. If the fix involves a simple filter or belt, you only spend a small part of the machine’s value on components. The cost depends heavily on whether you use original equipment manufacturer (OEM) parts or aftermarket alternatives. You can find the exact part numbers for your serial number in the official documentation or on the manufacturer’s portal.

If a hydraulic pump or engine component is the source of the trouble, the repair cost can reach a large portion of the machine’s current market price. Always get a written quote from a certified shop before authorizing major engine or hydraulic work. If you’re unsure about the complexity of a repair, check the service manual for the specific procedure; if the manual lists a special puller or diagnostic computer, don’t attempt the job yourself.

A common mistake is assuming that a “part swap” is always a plug-and-play event. If you’re replacing a sensor or an electronic control module, the system often requires a software handshake or calibration sequence to recognize the new hardware. Skipping this step leaves the machine in a permanent limp mode, costing you hours of troubleshooting.

Use this decision rule to gauge your path: if the repair requires removing internal engine seals or opening a sealed hydraulic transmission, outsource the labor. These tasks demand a clean-room environment to prevent microscopic debris from causing a catastrophic failure within ten hours of operation. If the task is limited to external bolt-on components, you can safely proceed with your own hand tools.

Leave a Comment