The most common reason for your Skullcandy Jib True 2 One Side Not Working is a temporary synchronization error between the two earbuds or a drained battery in the silent unit. You can usually fix this by resetting the connection through the charging case. If the earbud remains silent after a full charge and a reset, it may have a hardware defect. This guide helps you identify if the issue is a simple software glitch or a permanent failure that requires a warranty claim.
Why one side stops working

The primary cause for one earbud going silent is a breakdown in the Bluetooth pairing process. Your earbuds act as a pair, but they often communicate separately with your phone. If one earbud fails to “handshake” with the other during startup, it stays in a standby mode while the other plays audio. This is common if you pull them out of the case in the wrong order or if the case contacts are dirty, preventing one side from waking up.
Another frequent cause is a physical obstruction on the charging pins. The charging case uses small metal pins to power the earbuds. If earwax, lint, or dust builds up on the gold contacts of the earbud or the pins inside the case, the silent side won’t charge. Even if it looks like it’s sitting correctly, it might be running on a near-empty battery.
Finally, a firmware mismatch can occur if the earbuds were separated for a long time or if one unit didn’t update correctly. When this happens, the earbuds no longer recognize each other as a set. According to Skullcandy’s official support page, performing a manual factory reset clears these stored pairing profiles and forces the two units to re-sync as a single device. If you have tried these steps and the earbud still doesn’t produce sound or light up, the internal battery or speaker driver has likely failed.
Reset the connection manually
If only one side is playing audio, you must force the earbuds to forget their current pairing and start over. This fix is for users whose earbuds are clearly powered on but refuse to play sound in stereo. Start by removing both earbuds from your phone’s Bluetooth menu. Go into your settings, find the Jib True 2, and select “Forget This Device.” This ensures no old settings interfere with the new connection.
Next, place both earbuds back into the charging case. Leave the lid open. Press and hold the button on both earbuds for ten seconds. You’re looking for the LED lights to flash or change color, which indicates the reset process is starting. Once the lights show they have reset, take both out at the same time. They should now flash to indicate they’re searching for each other. If they successfully sync, one will stop flashing while the other continues to blink. This is when you return to your phone’s Bluetooth settings and select the Jib True 2 again. If you only see one earbud light up during this process, the silent one isn’t receiving power from the case. This fix isn’t for users who have physically damaged their earbuds or dropped them in water, as liquid damage creates electrical shorts that a reset can’t repair.
Clean the charging contacts
If the reset didn’t work, the silent earbud is likely dead because it can’t charge. This fix is for anyone who has used their earbuds daily for more than a few months. Over time, skin oils and debris create a thin layer of grime on the metal charging points. Even if the earbud sits in the case, it never gets the energy it needs to turn on.
Take a dry, clean cotton swab. Gently wipe the gold contact points on the bottom of the silent earbud. Don’t use water, soap, or rubbing alcohol, as these can seep into the housing and damage the internal electronics. Next, look into the charging case. Use the dry swab to carefully clean the spring-loaded pins. If you see dark spots or debris, give them a firm wipe. Once clean, place the earbud back into the case and watch the LED indicator. A solid red light means it’s charging. If the light remains off, try pressing the earbud down firmly with your finger for five seconds. If the light turns on while you press it but turns off when you let go, the internal spring in the case is likely worn out. This is a mechanical failure that requires a replacement case or a warranty claim through the manufacturer. Don’t force the earbud into the case with excessive pressure, as this can break the plastic housing.
Check for hardware failure

Sometimes, an earbud is simply broken. This fix is for users who have confirmed the earbud is clean and fully charged but still makes no sound. If you have performed the reset and confirmed the device is charging, but one side remains completely silent, you’re likely dealing with a failed speaker driver or a disconnected internal wire.
Check for a simple software trap first. Sometimes, a specific app or your phone’s “Accessibility” settings can shift the audio balance to one side. Go to your phone’s sound settings and look for a slider labeled “Balance” or “Left/Right.” Ensure the slider is perfectly centered.
If the balance is correct and you still hear nothing, the hardware is at fault. A common mistake is attempting a DIY repair by prying open the chassis. Because these units are glued shut with industrial adhesive, opening them almost always destroys the internal plastic clips and waterproof seals. You’ll likely lose your warranty coverage and end up with a useless, broken device.
If your product is within the warranty period, contact the manufacturer directly to initiate a claim. Don’t attempt to force the housing open, as physical damage from prying is easily spotted by technicians and will void your claim.
If you’re out of warranty, weigh the cost of a professional repair against the price of a new set. Most consumer-grade earbuds are sealed at the factory, meaning professional repair is rarely cost-effective. If the repair quote exceeds 40% of the retail price of a new pair, the smarter financial decision is to purchase a replacement.
What not to do
-
Don’t submerge the earbuds in liquid cleaners. This will destroy the internal electronics and void your warranty immediately. If you need to sanitize the surface, use a cloth lightly dampened with 70% isopropyl alcohol, but never spray liquid directly onto the mesh.
-
Don’t use metal tools to scrape the charging pins. You’ll scratch the gold plating, which causes permanent charging failure. If you see debris, use a dry, soft-bristled toothbrush or a wooden toothpick to gently dislodge the buildup without compromising the conductive surface.
-
Don’t attempt to pry open the earbud shell. The housing is glued shut, and you’ll snap the plastic clips, making it impossible to reassemble. If the audio becomes muffled, the problem is likely wax blockage in the nozzle, not an internal fault.
-
Don’t use a hairdryer to “dry out” the earbud. The heat will melt the internal battery and speaker components beyond repair.
How to stop it happening again
Consistency is the best way to keep your earbuds working as a pair. If you’re noticing syncing issues, use the following table to adjust your daily habits.
| If you’re doing this | Do this instead | Why |
|---|---|---|
| Storing them loose in a bag | Use the charging case | Prevents dirt from entering the charging contacts |
| Connecting one at a time | Remove both from the case together | Forces the earbuds to pair as a stereo set |
| Ignoring the LED lights | Watch for the red charging light | Confirms both units are actually receiving power |
| Using them until dead | Charge when the battery is low | Prevents deep discharge that kills battery life |
The most common mistake is assuming both buds charge simultaneously regardless of placement. If one bud sits slightly askew, the magnetic pins won’t engage, leading to a mismatched battery state. Always wait for the visual confirmation of the charging light before closing the lid.
If your earbuds still fail to sync, perform a hard reset by holding the touch sensors for ten seconds while they remain in the case. This clears the internal cache of previous connections. If the LED flashes white after this reset, your devices have successfully re-established their factory link. Use this reset method only when audio drops occur more than twice in a single hour.
Frequently asked questions

Can I use just one earbud at a time?
Yes, you can use the right earbud by itself, as it acts as the primary unit in most Jib True 2 models. If you try to use only the left earbud, it may not connect because it relies on the right earbud to maintain the master signal. If you find yourself needing to use only one side often, stick to the right one to avoid connection drops.
How long does a full reset take?
A full reset takes about two minutes of your time. You must spend the first minute forgetting the device on your phone and the second minute performing the button-press sequence. Once the earbuds flash, they usually pair to your phone within ten seconds. If they don’t appear in your Bluetooth menu after one minute, turn your phone’s Bluetooth off and back on to refresh the search.
Is it safe to use a toothpick to clean the pins?
No, it isn’t safe to use a wooden or plastic toothpick inside the charging case. You risk snapping the tip off inside the narrow charging port, which will block the pins and stop the earbud from charging forever. Stick to a dry, soft cotton swab or a clean, lint-free cloth to ensure no debris is left behind inside the case.
What happens if the earbuds get wet?
If the earbuds get wet, they may stop working because water creates a short circuit on the touch-sensitive controls or the charging pins. Immediately turn off your music and wipe them dry with a clean cloth. Let them air dry in a cool, dry place for at least twenty-four hours before you attempt to charge them again. Never use heat, as it pushes moisture deeper inside.
Why does the light blink red and blue?
The blinking red and blue light indicates that the earbud is in “pairing mode” and is looking for a device to connect to. This usually happens when the earbuds have been reset or can’t find the phone they were previously linked to. If only one is blinking, it means that unit has lost its connection to its partner or your phone. Put them back in the case to reset them.
Final Thoughts
If these troubleshooting tips don’t bring your sound back, don’t worry. You shouldn’t hesitate to reach out to Skullcandy’s support team through their website. They’re usually quick to help with warranty claims if your device is truly faulty. Getting back to your favorite music is worth the extra effort.
Related guides
- Jvc Ha ec25t One Side Not Working
- Powerbeats Pro One Side Not Working
- LG True Balance Washer Problems: Troubleshooting and Fixes