The Samsung Washer Code Sc Or 5C appears on your display when the machine fails to drain the water from the drum within the required time limit. This error code indicates a blockage or a mechanical issue preventing the pump from clearing the water, and you can usually fix it by checking the drain filter or the external hose. If the water doesn’t exit the tub within a few minutes, the controller stops the cycle to prevent flooding or motor strain.
What causes the Samsung washer code Sc or 5C

The primary cause for this error is a physical obstruction in the drain path. Small items like coins, hairpins, or buttons often get past the drum holes and lodge themselves in the pump filter. If the filter is clean, the next common cause is a kinked or clogged drain hose. When the hose is bent behind the machine, the pump works against too much resistance, which triggers the sensor to display the code.
Check the hose for a “kink” by pulling the machine six inches away from the wall. If the drain hose is forced into a tight 90-degree angle, the pump will fail to clear the water. You should ensure the hose has a gentle, sweeping curve rather than a sharp bend.
Another reason involves the drain pump motor itself. If the impeller—the spinning part inside the pump—is jammed by debris or has reached the end of its mechanical life, it can’t move the water. This varies by model; some machines feature a secondary “check valve” that can stick shut.
If you live in an area with very hard water, mineral buildup can also narrow the diameter of the internal hoses over several years. This reduces the flow rate significantly.
Finally, if your drain hose is inserted too far into a standpipe, it can create a siphon effect or an airlock. If your machine drains but then immediately refills, pull the hose back so it sits loosely in the pipe.
Clean the debris filter
This fix is for users who have access to the front bottom panel of their washer. First, turn off the power at the wall outlet. Place a shallow tray or a thick towel under the small door on the bottom right of the front panel. Open the door and pull out the small black rubber tube to drain any remaining water into a container.
Once the water stops flowing, turn the large circular filter cap counter-clockwise to remove it. You’ll likely see water rush out, so keep your towel ready. Inspect the cavity for coins, lint, or fabric scraps. If the impeller inside the hole doesn’t spin freely when you poke it with a finger, you have found the jam. Rinse the filter cap under hot running water to remove slime or debris buildup.
Screw the cap back in firmly by turning it clockwise until it’s tight. If you don’t tighten this enough, the machine will leak during the next cycle. This isn’t for those who can’t safely reach the bottom of the machine; if you have mobility issues, ask someone else to assist you to avoid straining your back. If the pump makes a loud grinding noise after you clear it, the pump motor might be damaged and requires a professional technician.
Clear the drain hose
If the filter is clean but the code persists, you must check the external drain hose. This fix is for those who can safely move their machine away from the wall. Pull the washer forward carefully to avoid scratching the floor or pulling on the water inlet hoses. Disconnect the drain hose from the standpipe or sink connection.
Check the entire length of the hose for kinks, bends, or flat spots. If the hose is crushed behind the machine, straighten it out and ensure it has a smooth path to the drain. Next, inspect the end of the hose for a “clogged” feeling or visible debris. You can use a garden hose to flush water through it to ensure it’s clear.
If the hose is positioned too low or too high, it will affect drainage. The end of the drain hose must be between 24 and 36 inches above the floor. If you find a crack in the hose, you must replace it with a genuine part. Don’t attempt to patch a leaking drain hose with tape, as the pressure of the pump will cause it to burst and flood your laundry area.
Inspect the drain pump connection

This fix is for cases where the machine sounds like it’s trying to pump but nothing happens. Sometimes, the electrical connection to the pump vibrates loose. You should only attempt this if you’re comfortable with basic mechanical tasks. If you’re not, contact a qualified repair service.
First, ensure the unit is unplugged. Remove the back panel of the washer to locate the drain pump assembly at the bottom. Check that the wire harness connected to the pump is pushed in fully. If the wires look burnt or melted, don’t touch them, as this indicates a short circuit that requires a professional.
If the wires are fine, check the pump housing for any signs of water leaking from the seal. If you see water stains or rust around the pump motor, the internal seal has failed and the pump needs replacement. If you’re uncertain about handling electrical components, don’t proceed. Always remember that a capacitor in the machine can hold a lethal charge even when unplugged; if you see a large cylindrical component, don’t touch its terminals. If the pump remains silent after you have verified the connection and confirmed the filter is clear, it’s likely that the motor has burned out and requires a replacement part from the manufacturer.
What not to do
Don’t use heavy-duty drain cleaners or chemical clog removers inside the washer. These agents generate heat that can melt internal plastic components and degrade rubber pump seals, leading to permanent leaks.
Don’t force the pump filter cap if it feels stuck. You risk snapping the plastic threads, which often requires replacing the entire pump housing. Instead, wiggle the cap gently while applying steady, inward pressure to dislodge debris.
Don’t ignore a grinding sound. Running a jammed pump for even a single cycle can burn out the motor windings. This mistake turns a simple debris removal task into a costly motor replacement.
If you see water siphoning back into the drum, pull the hose back until the air gap is restored.
How to stop it happening again
Regular maintenance prevents this error from returning by ensuring the pump stays free of small objects.
| If you’re doing this | Do this instead | Why |
|---|---|---|
| Washing items with loose coins | Use a mesh laundry bag | Prevents objects from entering the pump |
| Overloading the drum | Follow the load capacity guide | Prevents excess debris from washing off at once |
| Using too much detergent | Use the recommended amount | Reduces the buildup of sticky soap residue |
Most users mistake a quiet machine for a clean one. If you hear a faint rattling during the spin cycle, stop the load immediately. That sound is a coin or button trapped in the impeller housing. If you ignore it, the object will eventually crack the plastic housing, turning a simple cleaning task into a costly pump replacement.
The decision rule is simple: if the machine vibrates excessively, check the drain filter first. If the filter is clear but the noise persists, the object is likely lodged in the pump inlet hose. Don’t force the machine to finish the cycle. Doing so puts unnecessary strain on the motor, which can lead to a permanent electrical failure.
Frequently asked questions

Can I run the washer again after clearing the filter?
You can run the washer immediately after securing the filter cap and verifying there are no leaks. Run a short “Spin Only” cycle to test the drainage before starting a full load. If the code returns, a deeper blockage may exist in the internal hose.
Why does the code show up even when the tub is empty?
The code shows up because the water level sensor isn’t receiving a signal that the water has reached the “empty” threshold. Even if the tub looks empty to you, there may be a small amount of water remaining at the bottom that the sensor detects. Alternatively, the sensor itself may be faulty or clogged with debris, preventing it from reporting the true state of the drum to the main control board.
How long should the drain cycle take?
A standard drain cycle takes two to five minutes to clear the drum. This duration depends on the water volume and your drain standpipe height. If the pump runs longer than five minutes, the control board triggers an error code to prevent overheating.
Is it safe to leave water in the drum?
No, leaving water in the drum is unsafe because it promotes mold growth and unpleasant odors. Bail the water out manually using a bucket if you can’t fix the drainage issue immediately. Stagnant water can also damage inner tub seals, leading to costly repairs.
What happens if I ignore the error code?
Ignoring the code risks burning out the drain pump motor, causing a complete failure of the machine. Standing water can also cause drum bearings to rust or internal electronics to short out. Persistent issues often lead to foul smells that settle into the rubber gaskets.
Final Thoughts
If these simple checks don’t resolve the issue, it’s time to reach out to a professional technician for help. Don’t ignore a persistent drainage problem, as it won’t fix itself and could lead to bigger repairs later. You’ll be back to doing laundry in no time once the pump is working properly.
Related guides
- Samsung Refrigerator Error Code 40 E: Quick Fixes and Solutions
- Samsung Washer Sud or 5Ud Error Code: Quick Fix Guide
- Samsung Washer 4E Code